Home and Garden

The whirlpool oven says E2 and F3 locked, so how to fix it?

There is a list of Whirlpool Stove, Range, and Oven error codes.Error codes are displayed on your oven's display to let you know there is a problem.The list of Whirlpool oven fault code definitions will help you find the issue.The codes below can be used to clear, check, and fix your oven.You will know which part of the oven is faulty once you understand the error code.You can buy the part and fix the oven on your own.There are error codes on the ovens.Two sets of 2 digits with a letter and a number are what your oven will show.There is an example of a 4 digit error code.

Press and hold the Start or Cancel button for ten seconds to remove the LOC from the display.

If start is not pressed within 5 seconds, "PUSH" or "PSH" appears on the display, the function is canceled and time is displayed.

Unplug the oven power cord or turn off the circuit breaker if the error code is F1Reason/Condition for Error Code.

Check for welded contacts on both the bake and broil relays and replace parts if necessary.

The reason for the error code is the open oven temperature sensor.

The oven error code is F4Reason/Condition for Error Code.

There is an error code for the whirlpool oven.

Error code F7Reason/Condition for Error Code is related to the function key being stuck and the control board being replaced.

There is an error code for the whirlpool oven.

The whirlpool oven error code is F9Reason/Condition for Error.

Unplug the oven power cord or turn off the circuit breaker if you have a Whirlpool Oven Error Code F2 E0 (E0 F2).The wiring harness for the keypad.Turn on the circuit breaker if you want to plug the oven power cord back in.The display has a CANCEL on it.If the fault code comes back within a minute, replace the keypad.The electronic oven control should be replaced if F2 E0 persists.

Unplug the oven power cord or turn off the circuit breaker if you have a Whirlpool Oven Error Code F2 E5 (E5 F2).The wiring harness for the keypad.Turn on the circuit breaker if you want to plug the oven power cord back in.The display has a CANCEL on it.If the fault code comes back within a minute, replace the keypad.The electronic oven control should be replaced if F2 E5 persists.

Unplug the oven power cord or turn off the circuit breaker if you have a Whirlpool Oven Error Code F2 E6 (E6 F2).The wiring harness for the keypad.Turn on the circuit breaker if you want to plug the oven power cord back in.The display has a CANCEL on it.If the fault code comes back within a minute, replace the keypad.The electronic oven control should be replaced if F2 E6 persists.

Unplug the oven power cord or turn off the circuit breaker if you have a Whirlpool Oven Error Code F3 E0 (E0 F3).Remove the oven temperature sensor wiring harness.If the wire harness is shorted, replace it.Check the oven temp sensor resistance with an ohm meter.The oven temperature sensor should be replaced if resistance is not very high.The electronic oven control should be replaced if the oven temp sensor resistance checks good.

Unplug the oven power cord or turn off the circuit breaker if you have a Whirlpool Oven Error Code.Remove the oven temperature sensor wiring harness.If the wire harness is shorted, replace it.Check the oven temp sensor resistance with an ohm meter.The oven temperature sensor should be replaced if resistance is not very high.The electronic oven control should be replaced if the oven temp sensor resistance checks good.

The whirlpool oven error code is F3 E2.Remove the oven temperature sensor wiring harness.If the wire harness is shorted, replace it.Check the oven temp sensor resistance with an ohm meter.The oven temperature sensor should be replaced if resistance is not very high.The electronic oven control should be replaced if the oven temp sensor resistance checks good.

Unplug the oven power cord or turn off the circuit breaker if you have a Whirlpool Oven Error Code F3 E3 (E3 F3).Remove the oven temperature sensor wire.If the wire harness is shorted, replace it.Measure the oven temp sensor resistance with a meter.The oven temperature sensor should be replaced if resistance is not very high.The electronic oven control should be replaced if the oven temperature sensor resistance and wire harness connections are found to be a problem.

Unplug the oven power cord or turn off the circuit breaker if there is an error code.Measure the resistance of the meat probe with a volt/ohm meter.The meat probe should be replaced if resistance is not 59000.Check for a secure connection with probe and jack if resistance of meat probe is good.The jack should be replaced if it is worn.The meat probe jack has a wire harness on it.If needed, replace the wire harness.

The oven door switch can be tested by opening and closing the door.The oven light can turn on and off.If the oven door switch is malfunctioning, you should replace it.Turn off the circuit breaker if you want to unplug the oven power cord.The oven door lock assembly has loose wire harnesses.If needed, replace the wire harness.If the door lock assembly is faulty, replace it.

Unplug the oven power cord or turn off the circuit breaker if you have an Error Code.Remove loose wires from the oven door lock assembly wire harness.If needed, replace the wire harness.If the door lock assembly is faulty, replace it.

Replacement parts are associated with error codes.

If(typeof_ez_fad_position!= 'undefined');Whirlpool Terminal Block for Range Oven.

Are you in need of help with an error code on your appliance?We will be happy to assist you in fixing the problem if you leave your question below.

The heating elements have not been on overnight.Is there a switch that will flip to turn off the lighting?

The whirlpool range's bottom element was replaced after it started sparking and crackling.It was more difficult than shown in the videos because one of the connections had a short wire and kept disappearing into the insulation.I got an F9 error code when I reconnected.I can get into the test mode if I hit cancel twice, but start doesn't work.I unplugged the breaker panel for 5 minutes and it didn't work.The lock on the door seems to be working.Suggestions on what may be wrong.Thank you.

The Self-Clean function on my appliance has not worked for a long time.The oven does not heat to clean, the door is locked, and I can't open it.Every other function works well up to this point.

My stove top won't work.There is no error code or start button.

My stove is reading f2 e1 and f3 eo, what could be the problem, we have already replaced the sensor wire, but it is still flashing error F3 EO.

I have a barely 6 month old whirlpool stove, used once and the next day have E R R, F1, F0 and oven won't work, tried unplugging but still cannot use oven.

I have a whirlpool oven that is not heating properly and the display shows an error code, but I can't find it on the internet.

I have a double oven and the error code E2 F6 appears, I reset the circuit breaker, and if I hit the start button, the stove works, but what does this code mean?

There was a big thunder near our home.There was a message on the keyboard that said "keyboard disabled" and the lights inside the oven did not go off.The same thing happened when I unplugged the oven and plugged it back in.Is this fixable?

What is the meaning of the code E1 F1 on the gold glass top oven?The stove top works after the power went out, but the oven and clock display don't.

If there is an issue with the door, be sure to close it. The door switch may have a fault, so remove power to the oven.

I have a double oven built in by Whirlpool.An error code E6 F2 can be seen at times.I want to know what the code means and how to fix it.

When I want to bake, I press bake and it says clean, but it doesn't bake.Would the problem be the board?

There is an error of e1 f7 in my self-cleaning accubake system.Does anyone know what that means?Twice a time, it comes on.

Can the f1e3 code be fixed by resetting the whirlpool range?

I own a built-in oven and microwave combo.There is an error message near the end of the cleaning process when using the self cleaning feature.How can this be fixed?Thank you.

I own a gold series oven.An error code f5e4 came up when we turned on the oven cleaning system.The bottom of the oven has all hair line and spider web cracks.This can't be normal.Please tell me what to do.I have pictures of the error code and cracks.

I have the same problem.There are cracks and chippinig on the floor of the oven at the door opening.Have you ever received a solution to this issue?I want to clean my oven today, but I don't want it to get worse.Thank you.

I have an error code 5 coming up on my ikea whirlpool nutid mwc 6 microwave oven, if one of the boards needs to be replaced, please help me,regards simon.

I have a Whirlpool range model with an error code of 5a6 6ath or 5ab bath.Dennis, do you know what this means and how to fix it?

There is a whirlpool oven model.The broil and bottom elements should be replaced.The oven heating light blinks once but doesn't heat up.I want to know what is wrong with it.Top burners work well.

I tried to break the circuit and it came back with the error code F1-E2 on the clock display, what does this mean?The oven and stovetop are still working.Any other suggestions?I wonder if this is just something I can ignore, because I cannot afford a new part.

Everything was fine when I was baking.The oven said there was an error and to press start and then cancel.I can't turn on the oven settings.The feature is not available.

I used the Accubake range from the Whirlpool ceramic top range.The stove top does not work in the oven.There is a question mark by the start button.Start?

The range display will not do anything after a storm.The burners work but the oven light won't stay on, and all the buttons just chime when pushed.

I replaced the control unit of the Oven after it wouldn't heat over 280 degrees after 30 minutes.The auto test now says 1 failure.The fault is 0Do I need to order the lower oven bake element or return the control unit?

I can't find anything on the internet that says what the problem is with my whirlpool oven.

I have a gas oven that is showing an error code.It came back on after I cleared it.

I try to bake stuff but it's not hot.How do I fix that error code?

After an overnight power failure, awoke to a Whirlpool oven clock 20 minutes fast. Attempted to correct clock and it produced 5A6 error code.After turning off breaker for 10 minutes, panel displayed 30 for a few seconds.

I put a loaf of bread in the oven when the door locked and the error code e2 f 3 appeared, so I canceled and "cool" came on.After shutting off the power, the door wouldn't open.I can't get my meatballs out of the oven.As the power stays locked and starts heating up again, we don't dare turn it back on.What can I do?

When I try to use the oven it comes back with the error code F8EO.

What can I do to fix the error code?

Will the missing oven bake elements cause an error code of E6 F2 on the display panel?

I started the self clean option when I was 8 years old.I returned later to find the door ajar and the lock out, but not in use.The E0 F5 error is on my screen.Is there a way to disengage the lock.

The whirlpool oven says E2 and F3 locked, so how to fix it?

Related Posts: