I am having trouble with my Amana washing machine, it won't run but the fill light is blinking

You can save time and money if you know how to fix your washing machine.The following steps should help resolve most issues with these washers.

tap the text to operate if your washer has an electronic touchpadHold the control lock button for 3 seconds if the lock is on.

Before pressing the start button, make sure the knob is completely lined up with the cycle selection.The cycle will not start if the knob is not in sync.

The door may be open, but not locked.Try closing the door.

Less water is removed from cycles with slower spin speeds.To find a solution to the problem.

The load may not spin correctly if it is tightly packed or unbalanced.Follow these instructions to get to the bottom of the problem.

If you use too much detergent or use regular detergent, it can slow or stop draining.The only detergent you can use is HE.Measure and follow manufacturer's instructions.To remove extra suds.

There may have been small items stuck between the washer drum and the outer tub.Follow the instructions to resolve the problem.

Only use the wash and dry cycle for lightly soiled synthetic garments.

The lid lock light will flash if the lock has not moved into the locked position, the motor cannot be powered, or the lid is not closed completely due to interference.Some washers will lock immediately, while others will not lock until after the wash cycle starts.

There are excessive suds in the washer when this error code appears.The washer is cutting suds.To fix:

You can remove load if "rL" appears in the display.The error occurs when the load is detected in the drum.

The control of your washer is locked when loc appears on the display.There is an indication that the control is locked.

The code appears on the display as a system error code.Follow the steps to clear the error.

If power was lost while running a cycle, the error code appears.The steps below will clear the error.

The code indicates that your washer detected an off balance load and that caused the cycle to take longer than usual or the clothes to be more wet.To clear the error.

The washer door was not opened between cycles.Try these steps to clear the error.

The codes on the display signal a water supply error.To clear the error, you need to check the water supply.Try following these instructions.

The code shows a drain pump system error.It is possible that it is a result of incorrect drain hose installation.It is possible that it is a result of using too much or not using enough HE detergent.

The washer door is not locked when this error code is displayed.Follow the instructions below to clear the error.

If the Clean Washer lights up at the end of the wash cycle, it means the washer has run 30 wash cycles and is indicating a reminder to use the affresh cycle.

An invalid action was performed.The error code will be shown if there are certain conditions.

There are detergents that can slow or stop the washer.Don't use other detergents.Measure detergent according to manufacturer's instructions.

Before a new cycle can begin, the door must be opened and closed.

When the start/stop button is pressed and the water level knob is set to auto sense, the washer will fill and begin to sense load size and balance.The wash phase of the cycle will begin once the washer fills to the appropriate level for the detected load size.

Check your water supply lines if the fill light is on.The water lines should be turned on for the washer to operate.

When the unlocked lid is open, the sense and wash phases will be paused.The cycle can be resumed if the lid is closed.The washer will not cycle and pump out the water if the lid is open for more than 10 minutes.After the wash phase, the lid will lock and remain locked for the rest of the cycle.

There is an issue with the draining.The following instructions can be used to solve the problem.

Less water is removed from cycles with slower spin speeds.To find a solution to the problem.

The load may not spin correctly if it is tightly packed or unbalanced.Follow these instructions to get to the bottom of the problem.

If you use too much detergent or use regular detergent, it can slow or stop draining.The only detergent you can use is HE.Measure and follow manufacturer's instructions.To remove extra suds.

Related Posts:

1. How to fix/and what's causing play store error df-dla 15 onSamsung...
2. Carrier AC Error Codes, Carrier Dc Inverter Air Conditioner EC Error Code, and Carrier Jasa service ac error codes are listed.
3. What are these white patches of saliva on my pillow?
4. PDF Rekeying Quick Start Guide - Schlage how to rekey a lock cylinder.