A guitar nut is located at the end of the fingerboard.The strings are held in slots and the string spacing is defined.If the slots on your guitar get worn out, or if you change the size of the strings or spacing, you may need to replace the guitar nut.You need a pre-slotted drop-in replacement nut and some basic tools to do that.If you want to replace the nut, first you have to remove the old one, then you can drop the new one in and make minor adjustments.
Step 1: The guitar strings should be removed.
The tension of each string should be loosened with the tuning keys.Pull out each bridge pin that holds the strings to the bridge at the bottom of the guitar with needle-nose pliers.Put the strings aside.Since you already have to replace the guitar nut, you can take advantage of this opportunity to put new strings on your guitar.
Step 2: You can score around the guitar nut with a craft knife.
To prevent lacquer from sticking to the nut when you knock it loose, trace the finish around the edges with the tip of the craft knife.Take a look at where the nut meets the wood of the headstock.This will help free the nut from the lacquer and any glue that may have been used around it to prevent it from breaking when you knock it loose.Don't cut yourself with a craft knife.
Step 3: Place a block against the nut.
You can hit the back edge with a hammer if you use a wooden block that is thick enough.Place it against the long edge of the nut where the wood meets the fingerboard.The wooden block will help distribute the pressure of your hammer blows to knock the guitar nut loose all at once and avoid damaging the wood around it.
Step 4: To knock the nut loose, lightly tap the back edge of the block.
The wooden block should be placed against the long edge of the nut with 1-2 fingers of your non-dominant hand.Carefully wield a hammer with your dominant hand and gently tap the back edge of the wooden block to free the nut from the wood.This should only take one light tap.If the guitar nut doesn't come free after 1-2 light taps, try scoring around the edges with a craft knife.If you try to make it come loose by swinging the hammer harder, you might damage your guitar.
Step 5: The new guitar nut should fit where the old nut was.
The old nut was against the wood of the fingerboard so try to fit a new pre-slotted drop-in nut there.If you want to make it shorter, look closely at how it sits.The strings have to be able to clear the first fret so they don't buzz against it.If the old height was good, try to make the nut the same height as the new one.A little taller is better than a little short.You can buy guitar nuts online or at a music store.
Step 6: The guitar nut needs to be sanded down with 800- or 1000-grit sandpaper.
Place a piece of paper on a work surface and secure it with masking tape.Sand the bottom of the nut a little bit at a time, testing it on the guitar as you go, and stop when you are happy with the height and fit.Remove a small amount of material at a time.The guitar nut will be too close to the wood of the fingerboard if you remove too much.If there is any overhang, sand the ends of the guitar nut.When the nut is resting in the slot, remove only a bit at a time.
Step 7: When you are happy with the fit, glue the new nut in place.
The underside of the nut has wood glue on it.Press it firmly into the slot.It should be left to dry for 24 hours.It is not recommended to use permanent glue, such as superglue, to attach a guitar nut because it will make it very hard to remove and can result in damage to your guitar if you ever want to replace it again.
Step 8: The string slots have a tip for a pencil.
To color in the string slots on the new guitar nut, use a regular wood and graphite pencil and a yellow one.The strings can get caught up in the new nut when you install them.This is a good time to clean the old strings.
Step 9: Remove the strings on the guitar.
Put the bottom ends of the strings back into the bridge, secure them with bridge pins, and wind the top ends around the tuning posts.Use the tuning posts to tighten the strings and tune the guitar to the right pitch.If you press down on the third note of the top string, you can see if there is a gap between the string and the first fret, which is less than the thickness of a credit card.Your strings are resting at a good height if that's the case.