How to Remove Plasti Dip is an easy to follow step by step guide.
Are you looking to remove the plasti-dip from your car's wheels?If you've decided you don't want the coating on your car, you can find the safest and easiest ways to get it off.
There is a wide range of automotive applications for plasti dip.There are a lot of things you can do with it.
If you are reading this article, you probably don't want this substance on your car because of a number of different reasons.You regret dipping your car.
You are doing the right thing by researching this first if you are not sure how to start your vehicle.
We are here to tell you everything you need to know about how to remove plasti dip from your car.
We have set out step-by-step guidelines for each approach so you know exactly what to do.
The rubber coating is supposed to be easy to peel off.The reality can be different, and removal is not always easy.
It will be difficult to peel it off if you didn't apply it evenly.The thinner layers are likely stuck.
It can be difficult to remove the thin layers of awkwardly-shaped surfaces.If you use too much force, you run the risk of scratching the surface.
You can remove the bulk of the thick coat of plasti dip.Smaller pieces might remain behind large sections that come off without much effort.
Picking them off one by one can be time- consuming and frustrating if there are lots of them.People don't want a car that looks patchy.
Before we dive into the ways you can get your car clean again, let's talk about what you need to avoid.
Some strategies could end up scratching away more than just the rubber coating, so stay away from them.
You should not use knives or metal-edged blades on your vehicle.There is no guarantee that you will not make a mistake.
Is it worth taking such a risk to get the offending substance off?
A bottle or two of a heavy-duty chemical can be found at home.Maybe it is an acid that eats through rust.
This is not the time to experiment.Some of these chemicals might be able to eradicate plasti dip, but at what cost?You could cause a lot of damage to your vehicle.
Don't attempt to create your own plasti dip removal solution.It is very dangerous to mix solutions or use them for something other than what they were intended for.
Let's discuss what you can do to remove this product from your vehicle after you know what not to do and why it is important to avoid doing it.
If you haven't already, gently peel off the plasti dip as much as you can.For which parts peeling off didn't work, this will leave less for you to take off using other steps.
The thick coating that could have been simply peeled away from your plasti dip removal product will be avoided.This will save you money.
Pick away in the middle.Start from the corners or edges of the part you are clearing.
It's more likely to tear off if you rip it off quickly.You should go as slowly as possible.
It is a multi-purpose lubricant for those who aren't familiar with it.Most people have at least one can in the garage, due to how many tasks they need this product for.
If you don't want to buy a specialty product to remove the plasti dip from your car, you can try WD-40.
The can has a wand instead of a spray nozzle.A spray bottle will make the job go faster if you have a lot of glue.
Make sure you don't leave any part dry by spraying the lubricant on the leftover plasti dip.Rub it in with microfiber cloth or paper towels.
Don't let extra drips beyond the surface you're treating, such as underneath the hood of your car.Taking precautions is always preferable when it comes to the inner workings of your vehicle.
To clean the WD-40, use a fresh microfiber cloth.The rubber coating should come off.
Take out your scraper or razor for stubborn bits.Pull at the pieces with a sideways motion.
Pushing down too hard may scratch your paint, plastic, or metal, so be careful not to use too much force.
Put warm water and soap in a bucket and rinse off the area you are working on.
The surface should not feel greasy or tacky.Don't wash until the traces of theWD-40 are gone.
It is difficult to remove the rubber coating on your vehicle.
It should be deep enough to soak your paper towels without much effort.
If you have a lot of coating, don't treat it all at once.Do them by section.
Don't let the fluid trickle through to your engine compartment if you're targeting your hood.When working near the edges, be careful.
Put the paper towel in the liquid.Remove it and place it on the leftover glue.
Place the wet paper towel over the rubbing compound.Put another sheet over it if it isn't sticking.If you want to treat the whole surface, repeat until it's covered.
Keep an eye on things.The solvent should break down if all goes well.
The spots of color on the paper towels are a sign that the rubber coating is soft.
There is a soft substance underneath.It should come off easily at this point.
You just washed the part with soap and water.Make sure you do a thorough job to get rid of the mineral turpentine.
Depending on the size of the area you are treating, you may be working for a while.
It is important to make sure the sheet is saturated.It will fall apart before you can put it on your car.
If you want to remove the rubber coating patch, set the wet sheet over it and repeat.
Don't be concerned if it seems like no action is being taken.You wouldn't see spots on the paper towels like you would with turpentine.
Like other solutions we have discussed so far, Goo Gone should not melt away coating.The whole patch should be loosened from the car's surface.
Take the paper towels away.You should be able to remove the underlying glue without much effort.
There are some pieces sticking to your car.Just repeat the steps above and they should come off.
You can try out a dip-dissolving product if none of the methods appeal to you.
You should read the guidelines for your dip dissolver.You have to wear gloves and a mask if you want to stay away from harm.
The rubber coating may have to be removed.It depends on the strength of the product.
You might not be able to use any of the above methods if you don't have the time or inclination to do it yourself.
If that's the case, you can call your local detailing shop and ask for a quote.You will save money if you solve the problem yourself at home.
Not all professionals will be able to remove plasti dip from your car.Businesses may only recommend products if they want to do the job.
It was probably the last thing on your mind when you first applied this rubber adhesive, until you decided you wanted it gone.
If you follow a simple list of steps and gather the necessary equipment, you should be able to do this yourself.If you purchase similar products for your car in the future, be aware of the removal process.
When it comes to the amount of effort required, application and removal can be vastly different, so keep in mind that you don't want to bite off more than you can chew.
I've always had an obsession with cars, from karting and motocross to collecting and obsessing over scalextric, matchbox and radio controlled cars.
I've learned through books, trial and error, and more knowledgeable family members that I enjoy tinkering with the mechanics and electronics of my vehicles.
I started this site as a place for me to share my knowledge, to teach others how to care for and maintain their vehicles themselves, so they can save a lot of money compared to always seeking out professional help.