You don't have to worry if you want to smoke out of a bong but you do not have one.You can use a few simple tools to make your own water bottle.It's a good idea to use it in a place where smoking is legal.
Step 1: Get a bottle.
The bottle you use for bong-making needs to be the right size.The plastic water bottle should do the trick.Water bottles are better than soda bottles because they don't leave sticky messes.If you want, you can remove the label.There is no need to leave any water in the bottle.You can leave some in to weigh it down if you want the bong to stand upright.This is not a traditional bong because it doesn't force the smoke through the water, but it can be made quickly and easily.
Step 2: The lid should be removed.
Set it aside.You won't need it.
Step 3: Remove a small piece of foil.
The bowl will be served by this piece.It should be 2.5 inches by 5 cm.If you want to get the best results, you should use heavy duty aluminum foil.If you only have lightweight aluminum foil, you can make it thicker by folding it over.The piece of aluminum foil should be large enough to cover the bottle's mouth.Take off a larger piece of aluminum foil if the bottle isn't large enough.
Step 4: The foil needs to be applied.
Wrap the edges of the foil around the bottle.The foil should be extended into the center of the opening.It should be a depression in the top of the bottle.The bowl should be large enough to hold your herb, but not so large that you tear the aluminum foil.If it is mishandled, aluminum can be toxic.
Step 5: There are holes in the bowl.
It is likely that 5 or 6 holes are adequate.To poke holes, use a needle, straight pin, toothpick, or other slender object.Make sure that the holes are not too close together.Don't poke holes so large that they break the bowl.
Step 6: There is a hole in the bottle.
Just above where the label stops, poke another hole in the outside portion of the water bottle.You need to place your mouth here.The hole shouldn't be too big.To make a bigger hole, poke a hole with a needle or straight pin and wiggle it around a bit.
Step 7: Use a pair of scissors to make the side hole bigger.
It needs to be 1 inch in diameter to start.Be careful not to rip the bottle; press down on the hole and gently enlarge it.The hole should be on the small side.You can enlarge it later, but you can't make it smaller.
Step 8: The bowl needs to be packed.
Put your favorite herb in the aluminum foil bowl.You can add more later, but you don't want it spilling over the sides.The holes you punched are too large if pieces of your herb fall through the bowl.If you want to make smaller holes, take the aluminum foil off.
Step 9: There is smoke.
Put the hole in the side of your mouth.Let the smoke from the bong fill the water bottle.
Step 10: Take a deep breath.
As you light the bowl and smoke fills the water bottle, set down the lighter and gently inhale the smoke in the bottle.
Step 11: You have to get a bottle.
A standard 16.9 ounce water bottle can work just as well as a two liter bottle.The bottle should be thrown out if the lid is not removed.
Step 12: There is a plastic pen.
The pen shaft needs to be used as a smoke shaft.A hollow cylinder will work with any plastic pen that can be taken apart.
Step 13: The bottle has a hole in it.
Carefully poke a small hole in the side of the bottle, which is 1/3 the distance from the bottom.The pen shaft will extend into the water.
Step 14: The pen shaft needs to be inserted into the hole.
Attach the pen to the hole at a downward angle.It will be hard to get a tight seal if the hole is too big.The bong can still be salvaged if the hole is too big.Place pieces of tape where the pen shaft meets the bottle to make a tighter seal.
Step 15: The bottle has a car in it.
There is a small hole on the opposite side of the bottle.This will be used when you are smoking.
Step 16: Attach a bowl.
Fix the outside end of the pen shaft.A seal can be made with a few layers of duct tape.The bowl is the sockets.There are metal sockets that are the right size.You can find a suitable object by looking around your house.If you can't find what you're looking for, visit a hardware store.
Step 17: Put water in the bong.
Water can be poured into the bong from the top of the bottle.It should be filled approximately 1/6 full.
Step 18: The bowl should be packed.
You can place your favorite herb in the metal bowl.You can add more later, but you don't want it spilling over the sides.
Step 19: The bong needs to be moved.
Place your mouth at the top of the bottle.The bowl should be facing away from your body if you tip the bong.
Step 20: Light the bowl.
Using a lighter, ignite your herb and begin to suck in slowly to force the smoke through the water.Make sure to place a finger over the hole.
Step 21: There was smoke.
When the bottle is full of smoke, set the lighter down.You need to remove your finger from the hole.Take the smoke out of the bottle.