How to change a door gasket on a front loader washer is one of the ways to clean it.
If the door on the washer is kept closed when not in use, the rubber gasket will be destroyed and mold will develop.This can lead to tears in the gasket that leaves water on the floor and a messy clean up.To prevent problems, replace the gasket and clean the inside regularly.A new front-load washer door gasket, boot or bellows can be replaced in less than an hour.
If the door on the washer is kept closed when not in use, the rubber gasket will be destroyed and mold will develop.This can lead to tears in the gasket that leaves water on the floor and a messy clean up.To prevent problems, replace the gasket and clean the inside regularly.A new front-load washer door gasket, boot or bellows can be replaced in less than an hour.
Make it easier to access the washer by moving it away from the wall.It's better to tilt it back against the wall.crumple up a towel in the place of the washer to protect the wall from damage.
The owner's manual has instructions on how to locate the screws.skip this step if you don't need to remove the boot.To remove the detergent feed tube, you need to detach the top, door, control panel and kick plate from the washer.You don't want to lose the screws if you put them in a can.Use the appropriate tool to remove the screws.You don't need to detach the control panel from the machine, just set it aside.
The boot is stuck to the lip of the opening with glue.You can run your finger beneath the boot.Use the utility razor to slice through the glue.The process should be repeated around the border of the opening.
The water-inlet tube is located in the upper left-hand corner of the front panel.Remove it from the boot.The wire is held in place by acounterclockwise twisting of the ends.The pliers can be used to open the flattened piece of copper tubing.The way to twist the wire is to slip the opening over the ends.Pull the inlet duct from the boot.
The door boot is in the washer.The lower portion of the boot needs to be grasped firmly.Roll, then push the lower edge inward over the lip of the front panel until you see the silver retaining ring or band that holds the boot in the channel.Use a flat-tipped screwdriver and needle-nose pliers to pry the retaining ring out.You don't want to bend it when you remove it.The gasket needs to be removed in the front.You will need the retaining ring for the installation of the new gasket.The inner portion of the boot can be accessed if you push the gasket into the washer tub.
Remove the inner side of the boot from the opening before the washer drum.The inner portion of the door gasket can be removed by removing the holding screws.If your model has a tab that sticks up to pull down gently on the boot, you will be able to extricate it from the channel.If you pull the gasket away, you can get to the retaining ring insert.The previous step should be repeated to remove the retaining ring.Pull the gasket from the inner channel if you don't have a ring.You will reuse the retaining ring if you set it aside.
The boot and ring sit in the inner and outer channels.To remove lint and laundry debris, use a clean rag and warm water.If you have a wet-dry vacuum, use it to suck out the dirt if it's wet, otherwise use a standard vacuum to clean the channels.
Put your finger in liquid laundry detergent to Lubricate the part of the boot that inserts into the front and back channels.It's easier to put the new boot in.
To install it, align the boot.Some boots have a small tab that goes into a slot on the machine for alignment, while others may have an arrow.The boot should be put in the opposite order of removal.Start at the bottom of the washer and work your way around the circle opening on both sides to the top.Place the ice cream stick into the channel.To hold the gasket in place, insert the retaining ring.The circular piece of steel should be inserted after the gasket.
Put the other components back in place.Put the washer on the floor and plug it in.
Related Posts:
- The best work boots for electricians can be found on the Best Work Boots for Electricians Page.
- How to clean a snowblower without removing it.
- attic ladders, Ladders, The Home Depot, Werner's Easy Access Attic Ladder 5 - Cut Ceiling Joists, things to consider before buying an attic ladder
- Is it worth fixing a car with a blown head gasket?