- Step 1: Locate the taillight access panel.
- Step 2: Unbolt the taillight housing.
- Step 3: Unlock the taillight socket.
- Step 4: Inspect the wiring.
- Step 5: Remove and inspect the bulb.
- Step 6: Replace the bulb with a brand new one.
- Step 7: Test out the new bulb.
Can you fix your own tail light?
Changing a faulty brake light is something anyone can learn to do. A replacement bulb costs about $10, and replacing it on your own will save about $20 in labor and the time it takes to travel to the shop and wait for the work to be done.
Why are my brake lights working but not my tail lights?
The most common reason your brake lights are not working but tail lights do is a bad light bulb. It can also be caused by a blown fuse, bad brake light switch, or issues with the wirings. This is a strange problem since, essentially, the connections for both lights come from the same source.
Can a blown fuse make your tail lights not work?
A blown-out fuse could cause your tail lights not to work. The car fuse looks similar to any other fuse out there. To check this component, you need to locate the fuse box first. However, as you inspect the fuse box, switch off the car ignition.
What would cause all tail lights not to work?
The most common reason why your tail lights are not working but brake lights are is due to a bad or wrong type of light bulb installed. It can also be caused by a blown fuse, bad wirings, or corroded sockets or plugs. A faulty control light switch could also be to blame.
How much does it cost to fix one tail light?
A new taillight switch, accounting for labor, will cost from $70 to $100. The plastic and colored lens over on top is a bit more pricey. Depending on the make and model of your car, a replacement taillight lens will leave you lighter by between $100, and upwards of $750.Jul 5, 2021
How do you reset tail lights?
https://www.youtube.com/watch?v=F8whjrksd0I
Where is the fuse for the tail lights?
The taillight fuse may be located in either the fuse panel in the front passenger side of your vehicle or in the main fuse box under the hood. Once you've opened either the panel or the main fuse box, locate the taillight fuse. If you're unsure which one it is, use the owner's manual for guidance.
What do you do if both tail lights go out?
Check the fuse. A blown fuse usually causes both lights to go out. On newer cars, the tail lamps can be fused separately and/or each bulb or shared circuit can be fused. A fuse can be blown due to other problems, so you'll need to check more than just the fuse, but it's the right place to start.
Which fuse controls the tail lights?
The taillight fuse may be located in either the fuse panel in the front passenger side of your vehicle or in the main fuse box under the hood. Once you've opened either the panel or the main fuse box, locate the taillight fuse.
Do tail lights have separate fuses?
On newer cars, the tail lamps can be fused separately and/or each bulb or shared circuit can be fused. A fuse can be blown due to other problems, so you'll need to check more than just the fuse, but it's the right place to start. On most newer cars it can be located under the hood or the dash.
How do you troubleshoot a tail light?
- Burnt bulb. For you to confirm your tail lights problem, you should check various elements.
- Damaged or dislocated wiring. To check the condition of your taillight wiring is easy.
- Blown-out fuse.
- Electrical problems.
- check Wiring.
- Check Turn Signal Switch.
Why does my brake lights work but not my tail lights?
Why is that? The most common reason your brake lights are not working but tail lights do is a bad light bulb. It can also be caused by a blown fuse, bad brake light switch, or issues with the wirings. Your vehicle's taillights are working fine, but the brake lights don't come on when you press the brakes.
How do you check a taillight fuse?
Once the fuse that controls your tail lights is identified, it can be tested using a fuse tester, which will light up if the fuse is good. If it doesn't light up, the fuse should be replaced with one of the same size and amperage. On certain fuses, you can visually see a break in the metal wire inside a bad fuse.
How do you test a taillight harness?
Test the taillight bulb socket with a digital multimeter Touch the black probe to a clean metal surface. Then probe the two terminals in the socket. You should see +12 volts. If the test light doesn't light, power isn't getting to the socket.
Where is the taillight fuse on a 2005 Chevy Malibu?
The taillight fuse in a 2005 Chevy Malibu can be found in the back of the vehicle near the left rear well. This is the auxiliary fuse panel for the accessories at the back of the car.
Is there a fuse for rear brake lights?
If your lights don't illuminate on either side and your brake light switch is good, then the next thing to check is the brake light fuse. Locate your vehicle's fuse box, which is usually under the hood or on the kick panel inside the passenger compartment. If it has, replace it with a fuse of the same resistance.
Why does my brake light work but not my taillight?
Why is that? The most common reason your brake lights are not working but tail lights do is a bad light bulb. It can also be caused by a blown fuse, bad brake light switch, or issues with the wirings. Either one light shines more than the other, or the taillights completely switch off when you press the brakes.
Are brake lights and tail lights the same bulb?
On many vehicles, the tail lights and brake lights share the same bulb. One filament inside the bulb is for the taillight and the other filament is for the brake light. There are also some vehicles that have a separate bulb for each circuit.
Where is the fuse for the rear tail lights?
Like all fuses, the brake light system fuse can be found in the power distribution center, which is under the dashboard or tucked away underneath the hood.
Where is the taillight fuse located on my 2004 Malibu?
It is located on the passenger side of the vehicle, on the lower portion of the instrument panel near the floor, behind the cover.
Why would both brake lights go out at the same time?
Bad Brake Light Switch When the brake pedal gets pushed, a switch is triggered to send a signal to the lights out back that it's time to turn on. If all three brake lights are out at the same time, it's unlikely that the trio of bulbs died simultaneously. In this case, it's more likely a bad brake light switch.