A leaking washer can be fixed relatively easily without the need for expensive help.You might be dealing with old hoses, a leaking pump, or oversudsing if you keep finding puddles of water on the laundry room floor.None of these problems will break the bank, because you'll need to fix them quickly.Doing these repairs yourself will save you time and money and give you peace of mind.The first thing you need to do is diagnose the problem, and once you have done that you can begin working to fix it.
Step 1: Make sure your washing machine is level.
If you want to figure out where the washer is leaking, you need to look at the water pooling in the machine.It will be difficult to know where the leak is if the washing machine is not level.
Step 2: Check for quick fixes.
If the leak is related to an issue that can be fixed more easily, you should replace the hoses and gasket.Make sure you read the machine manufacturer's instructions.If you try to load the washer with too many clothes, it can cause the water to leak out.If the washer has been loaded so that heavier clothes are on one side, it can cause an unbalanced washer.Adding more time while spraying can cause the spray to go on for longer than it's supposed to, leading to leak.The drain plug on your washing machine needs to be removed before you hook up the drain hose.The washer won't drain properly if you run the cycle without removing the plug.It could be the source of the leak if it's not attached correctly.When your drain is backed up, it might seem like the washer is leaking.Before doing repairs, make sure it's clear.
Step 3: Do you think oversudsing could be the problem?
Too much soap in the washer can cause overflow problems and lead to leaks.It's a common problem in households with water softeners, which make soap suds up more easily.You don't need to use as much soap if you have a water softener.Do a load of laundry to see if oversudsing is the problem.When you take the load out of the washer, put an article of clothing in a bowl of water.If the water gets sudsy, you're probably using too much soap, because your clothes still have soap in them.
Step 4: You can run a cycle and watch for leaks.
Do a load of laundry the same way you would normally do it, and check to see where the washing machine seems to be dripping.If you look for the spot where the water leaks from the machine, you can find out what the problem is.An old seal or overflow tube can cause leaks at the front of the washer.Damage to supply hoses can cause leaks at the back of the washer.A hole in the water pump is one of the causes of leaks under the washer.
Step 5: Replacing the most common parts is Methodically done.
If you can't pin down the exact cause of the leak, and you have an older washing machine, replacing or repairing the hoses and fixing the other most likely culprits is your best bet.Over time washing machine parts lose elasticity and can lead to leaks.They will need to be replaced eventually, so you should try to catch the leak now.If you don't want to make all the repairs at once, start with the first most common repair, run your machine to see if it still leaks, and make the next repair on the list.You should keep doing this until you fix the part.If your washing machine still leaks after all the repairs, you should call your machine manufacturer to see if they can help.It's time to call a washing machine repair person to finish the job.
Step 6: The power supply needs to be turned off.
If your washing machine's power supply is off, you can't make any repairs.While the power supply is on, it's a good idea to make repairs.
Step 7: The supply hoses need to be checked and repaired.
They feed water into the machine during the wash cycle.Old or damaged supply hoses can cause leaks at the back of the machine.If you have a supply hose leak, it will keep leaking throughout the wash cycle.The easiest way to repair water supply hoses is to turn off the water main.Remove the supply hoses with pliers.Look at the hoses.If the hoses are old and corroded, replace them with no-burst hoses and new washers.The internal washers should be replaced if the hoses are still in good shape.Old washers don't fit as tightly.Before using the washer again, make sure the connections are tight and secure.
Step 8: The internal hoses need to be checked and repaired.
The hoses inside the machine need to be replaced on a regular basis.You need to open the washing machine's cabinet or the panel behind which the hoses lie to get to the internal hoses.Look for old hoses and rusty hoses.To remove a hose, use pliers to squeeze the hose and then remove it.The old hoses and hose clamps should be replaced with new parts.
Step 9: Do you know if the pump is leaking?
The tub of the washing machine has a pump in it.It's made with internal seals that can wear out over time.If you see signs that the pump is leaking, it will need to be replaced.By the correct pump for your machine.You can open the washing machine's cabinet.The motor mounting bolts need to be loosened.Remove the pump hoses from the machine.The new pump should be used to replace it.You can find detailed instructions on how to replace a washing machine pump.